The Lotus 907 engine

The Lotus engine sat idle in storage for about 32 years. The compression readings were low and after a "leak down" test was performed, one could conclude the rings were stuck after so many years of inactivity. I decided to have it dropped off at the machine shop in Olean, Ny for a disassembly, and general checkover. The engine didn't need a complete rebuild by any means, but anything which hasn't been run to a long time deserves a general checkover while things are opened up.

The Engine was dropped off at Glen and Dicks Automotive machine shop and the exploritory surgery was performed by a machinist over a period of quite a few months.

Once the engine was broken down the piston bores honed and pistons re-ringed, I decided to replace the main bearings and all the gaskets at the same time. I also replaced 2 suspect valves which looked just a little worn.

The cost was extremely reasonable and the labor quality was excellent.

A breakdown of total costs follows:

1. Assemble and diassemble lotus 907 engine.............. $1320.00

2. Resurface flywheel and R+R pins............................... $60.00

3. resurface aluminum head.............................................$ 50.00

4. valve job (16 valve).......................................................$150.00

5. 2 replacement lotus valves............................................$ 18.00

6. gasket set..........................................................................$150.00

7. 1 set main bearings...........................................................$125.00

8. hone 4cyl block and align.................................................$90.00

9. sealant.................................................................................$38.00

10. Replace tensioner bearings............................................$24.90

11. Plugs ( soft... brass and stainless steel)........................$11.22

12. Degrease and clean engine.............................................$150.00

13. Check and polish crankshaft...........................................$50.00

14. R+R pistons on rods, glass bead, and hone pin bores..$60.00

Total Price................................................................................$2297.12

The attached picture shows the Lotus 907 awaitng the manifold, the carburators, and the other accessories before install.

Next.... new tires, engine install and a test drive...........

Kenny begins work on the car......

Ken Day, owner of Day Auto service in Great Valley, NY started working on the car after I ordered a bunch of parts from Delta Motorsports, and www.rejen.com across the pond. Jeff Peterson was given full "power of attoney" in my absence to make all decisions on the car restoration. He has done this three times before, so he has plenty of experience and I trust his judgement.

Brake System:

Kenny started out releasing the brakes and overhauling the Brake system on the Jensen GT. He repaired the Emergency Brake and flushed the brake lines. He replaced the front brake rotors and rebuilt the calipers. He added new high performance disc pads from Delta Motorsports. On the rear brakes, he turned the drums and replaced the drum brakes, wheel cylinders and wheel bearings. Kenny found the master cylinder was leaking badly. Instead of rebuilding the original, I elected to replace the master cylinder with a brand new direct replacement...... a TR6 Master cylinder. Once completed the car was topped off with DOT 4 brake fluid and tested. The brakes were now complete.

Fuel System:

The fuel tank was lowered from the bottom of the car and sent out for cleaning. The fuel lines were flushed and replaced where needed. The older mechanical fuel pump was removed and replaced with a new SU electronic version. The fuel filter was replaced with one placed before the two stromberg carbs.

Carburators:

The 2 stromberg carbs were leaking badly. The seals were worn. The rebuild kits contain about 12 different gaskets and 4 replacement parts. This will usually get them running well, and since the car only has about 26,000 miles, this should be enough. The cost to rebuild a set of carbs is about 2 hours labor and the cost of the rebuild kits. This usually runs about $150.00. If this doesn't work, the carbs have to be sent out to a specialty shop which will promptly replace all the worn items..... valves, fuel metering needles, as well as any adjusting screws, and will rebuild the entire linkage. This costs about $500.00. Usually, unless the condition of the carbs is obvious, most people try the cheaper route first.

Cooling system:

The original water pump was leaking badly and making a little noise. In a Lotus, this is never a good thing and it a sign of bad things too come. I had Kenny remove the water pump and send it out for a complete rebuild. The new water pump design really improves the cooling efficiency in the lotus. My other Jensen also has the new style pump, and I have never had a problem.

The Radiator was not as easy. The car was missing a radiator. Most people would think this is an easy thing to replace. Well, not really, as there are only about 250 of these car shipped to the United States and it is a completely different radiator than the Jensen Healey. When attempting to equip the Jensen GT with a radiator, there are only two options.

1) Go to a specialty radiator shop like www.wizardcooling.com, and pay them to design and build a custom aluminum radiator.

2) Call rejen across the pond and talk to Alison. She and her husband own the place and completely restore all models from Jensen motors. They have stockpiles of NOS ( New Old Stock) parts for the GT. She just happened to have a Brand New Jensen GT radiator in stock sitting on the shelf. I bought the radiator from Rejen and it arrived about 3 weeks later. It was in perfect condition, but I wanted to modify it correctly so it would not overheat as easily. The local radiator changed the internal cores from " 2 Row" to "3 Row". This will greatly improve the cooling ability of the radiator. At the same time, I had the radiator shop add a drainage tap so I can drain the coolant easily. Now, I just twist a lever and the coolant pours out of the radiator without removing the radiator hose and spilling it all over the garage.

Hoses belts and other things.......

Kenny replaced the timing belt ( which is very critical), the alternator and air conditioning compressor belts as well as most of the other rubber hoses under the hood. This car needs a timing belt replaced every 8- 10,000 miles or so. Kenny removed the original brake hoses and replaced them with custom stainless steel brake lines. It is only good maintenance practice to replace the radiator hoses, vacuum hoses, heater hoses, and oil cooler hoses.

Next up is the engine and bodywork.....

Taking Inventory for the restoration

Jeff and Laura Peterson were kind enough to check out the Jensen GT for me and arrange for an initial inspection by their trusted mechanic "Kenny" from Day Auto Service in Great Valley, NY. This would help me prioritize work and order parts before the restoration actually begins. Some parts can take months to procure but most parts can be found at "Delta Motorsports" in Arizona and the JHPS ( Jensen Healey Preservation Society) Club Store.

In the hatchback of the Jensen GT, Jim included a great deal of parts for me to utilize when restoring the GT. He put a spare windshield in the back to replace the cracked one presently on the car. This was a huge help as they are very expensive to replace and coupled with the high shipping costs from Arizona ( if they have them in stock), replacement costs alone for the part can reach about $750.00.  He included  stromberg carburator rebuild kits and all the manuals and other documentation which originally came with the car.  Jim removed at some point, all the emission engine controls, pumps, and hoses, which was great. In the mid 70's emission controls were added to cars and in the US, this was mandatory. It bogged down the Lotus 907's power. They added the stuff on to the engine without modifying it too much.  They added originally in 1976 the following things which attributed to loss of pickup and power as well as contributed to OVERHEATING and increases maintenance:

1) Catalytic Converter

2) Anti- run on System

3) AIR PUMP

These things were already taken off the vehicle and stored in the hatchback of the Jensen GT. I will definately will not be needing these again. Once these things were taken off, I can only imagine performance must have improved. In fact, every GT which I have seen restored, does not have any of these controls installed. Mine will not either.

The car was missing a radiator and a few marker lights on the right side. That was it. Besides minor body work on the right side of the car and some  interior refinishing ( headiner, new carpet, dash, and seat covers), the car was basically in very good shape.  Having already restored a Jensen Healey from the ground up, I am very familiar with all the hoses, belts, brake and fuel lines which will need replacing as well as all the upgrades which are now available for the engine. 

Some of the new upgrades items which are available for the Jensen Healey/GT are:

1) New improved water pump ( The original is completely rebuilt and new, better designed parts with longer wear are now available. The car is less likely to overheat as new improved bearings are used and better seals making leakage a thing of the past)

2) New improved Gear shift kit. This kit was designed by a retired engineer ( Pete Bahr). I send him the original shifter linkage and Pete rebuilds the entire assembly utilizing aluminum bushings to replace the fast wearing plastic bushings. The assembly once completed allows crisp shifts with no more trouble "finding" the proper gear.

3) Inproved Lucas alternator...... Well, it's Lucas, but it is supposed to be better than the original. It gives a little more power than the original with better  longtivity.

4) New electronic SU fuel pump to replace the original mechanical version.

5) Petronix ignition - Allows reliable starts and end the replacement of points  and condensor on a regular basis.

6) New three Core Radiator to replace the original 2 core radiator. Solves the cooling problem once and for all with combined with the improved water pump.

7) Dimmer switch and dashboard light upgrade. It took almost 30 years to come up with these but what a wonderful upgrade. The Dimmer  switch is a modified Jaguar XJ6 85-87 and the new bulbs actual put out enough light to see the instruments at night without putting excessive draw on the electrical system. Frank Schwartz, from Hendersonville, TN designed this upgrade. After this upgrade is done, the driver actually had to turn down the dimmer switch so the lights are not too bright.

8) Headlight relays..... allows brighter headlights and less electrical power going through the headlight switch.

9) Air Conditioning - Change parts for the new environmentally safe "gas"

10) Replace original "eyebrow" interior console lights with New super bright  bulbs  and red Lenses.

If I was rebuilding the engine completely, there are many options available, but a complete rebuild will not be necessary as this car has low mileage of 26,000 on the odometer.

It's a Great looking Jensen GT

I emailed Jim and received a quick reply along with some pictures of the car. He was in the middle of moving some things at his sisters place and the Jensen GT was one of his cars which he had stored at her house. He emailed me some initial pictures and described the condition of the car as best he could. The car looked beautiful and although it needed a bit of TLC, it was in much better shape than many Jensens which need restoration today. Jensens came from the factory with NO RUSTPROOFING applied to the car. My Jensen Healey which I restored in 2005, needed the usual mechanical systems rebuilt, but it also needed quite a bit of bodywork. Bodywork with my first Jensen Healey was something which started out as "minor" and ended up as "major"as more rust was discovered as things were inspected and slowly uncovered. Even the most knowledgable body man can not see the extent of corrosion to the naked eye. Jim was confident this Jensen GT did not have any rust and upon later inspection he was absolutely right.

Over the long storage time, the brakes had frozen to the drums, which made the car difficult to move. Jim needed the car moved off his sister's property with out delay, so I hired a tow truck with a flat bed to winch the car onto the deck and move it safely. I promised Jim I would restore the car to its original condition, and would start to work on it as soon as the car arrived in New York with my friends Jeff and Laura. It was a wonderful gesture to receive such a nice car, I sent down the biggest Maine Lobster Dinner I could find for Jim and his family. I thought it was the least I could do.

I received the car from the shipping company about three weeks later. I had it shipped to Salamanca Ny as my friend Jeff Peterson graciously agreed to look after the car as I planned the restoration from various providers in the Salamanca area. Since Jeff has fully restored 3 Jensens, he had access to a slew of people with Jensen experience. I figured I would come up and visit every few months and plan out each step of the restoration as my time and budget permitted.

Attached are some pictures of the car the day it arrived in NYC.